View APL1086_219943.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

APL1086
1.5A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.8V, 2.5V, 2.85V and 3.3V
Features
* * * * * * * * * *
Guaranteed Output Voltage Accuracy within 2% Fast Transient Response Guaranteed Dropout Voltage at Multiple Currents Load Regulation : 0.1% Typ. Line Regulation : 0.03% Typ. Low Dropout Voltage : 1.3V Typ. at IOUT =1.5A Current Limit : 1.5A Min. at TJ=125C On-Chip Thermal Limiting : 150 C Typ. Adjustable Output : 1.25~10.7V Standard 3-pin SOT-223, TO-252 , TO-220 and TO-263 Power Packages.
General Description
The APL1086 is a low dropout three-terminal adjustable regulators with 1.5A output current capability. In order to obtain lower dropout voltage and faster transient response, which is critical for low voltage applications , the APL1086 has been optimized. The device is available in an adjustable version and fixed output voltages of 1.8V, 2.5V,2.85V and 3.3V, the output available voltage range is from 1.25~10. 7V with an input supply below 12V. Dropout voltage is guaranteed at a maximum of 1.45V at 1.5A. Current limit is trimmed to ensure specified output current and controlled short-circuit current. On-chip thermal limiting provides protection against any combination of overload that would create excessive junction temperatures. The APL1086 is available in the industry standard 3pin SOT-223, TO-252, TO-220 or TO-263 power packages.
Applications
* * * *
Active SCSI Terminators Low Voltage Logic Supplies Battery-Powered Circuitry Post Regulator for Switching Power Supply
1 2 3
Pin Description
TAB IS VOUT
TAB IS VOUT
1
2
3
ADJ/GND OUT
IN
ADJ/GND OUT
IN
Front View for SOT-223
Front View for TO-252
ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright ANPEC Electronics Corp. Rev. A.4 - Jun., 2003 1 www.anpec.com.tw
APL1086
Pin Description
3 2 1 VIN VOUT ADJ
TA B is V O U T 3 2 1 V IN V OUT AD J
Front View for TO-220
Front View for TO-263
Ordering and Marking Information
APL1086H a n d lin g C o d e Tem p. R ange Package Code V o lta g e C o d e Package Code F : T O -2 2 0 G : T O -2 6 3 U : T O -2 5 2 V : S O T -2 2 3 Tem p. R ange C : 0 to 7 0 C H a n d lin g C o d e TU : Tube TR : Tape & R eel V o lta g e C o d e 1 8 : 1 .8 V 2 5 : 2 .5 V 2 8 5 : 2 .8 5 V B la n k : A d ju s ta b le V e rs io n AP L1086 XXXXX
3 3 : 3 .3 V
A P L 1 0 8 6 F /G /U :
AP L1086 XXXXX 18 AP L1086 XXXXX 25 AP L1086 XXXXX 285 AP L1086 XXXXX 33 AP L1086 XXXXX
XXXXX
- D a te C o d e
AP L1086 V :
X X X X X - D a te C o d e
A P L 1 0 8 6 -1 8 F /G /U :
XXXXX
- D a te C o d e
AP L1086- 18V :
AP L1086 XX XXX 18
X X X X X - D a te C o d e
A P L 1 0 8 6 -2 5 F /G /U :
XXXXX
- D a te C o d e
AP L1086- 25V :
AP L1086 XX XXX 25
X X X X X - D a te C o d e
A P L 1 0 8 6 -2 8 5 F /G /U :
XXXXX
- D a te C o d e
AP L1086- 285V :
AP L1086 XX XXX 285
X X X X X - D a te C o d e
A P L 1 0 8 6 -3 3 F /G /U :
XXXXX
- D a te C o d e
AP L1086- 33V :
AP L1086 XX XXX 33
X X X X X - D a te C o d e
Absolute Maximum Ratings
Symbol VI TJ Parameter Input Voltage Operating Junction Temperature Range Control Section Power Transistor Storage Temperature Range Lead Temperature (Soldering, 10 second) Rating 12 0 to 125 0 to 150 -65 to +150 260 Unit V C
TSTG TL
C C
Copyright ANPEC Electronics Corp. Rev. A.4 - Jun., 2003
2
www.anpec.com.tw
APL1086
Electrical Characteristics
Symbol V REF Parameter Test Conditions APL1086 Min. Typ. Max. 1.225 1.250 1.275 1.782 1.800 1.818 1.764 1.800 1.836 2.475 2.500 2.525 2.450 2.500 2.550 V 2.822 2.850 2.878 2.792 2.850 2.910 3.267 3.300 3.333 3.235 3.300 3.365 Unit V
V OUT
REG LINE
REG LOAD
VD ILIMIT IADJ IADJ
10mA IOUT 1.5A, 1.4V(V IN -VOUT) 9.75V, Reference Voltage T J =0~125C Output Voltage APL1086-18 T J =25C, IOUT =0mA, T J =0~125C, 0 IOUT 1.5A, 3.5VV IN9V, APL1086-25 T J =25C, IOUT =0mA, T J =0~125C, 0 IOUT 1.5A, 4VV IN9V, APL1086-28 T J =25C, IOUT =0mA, T J =0~125C, 0 IOUT 1.5A, 4.25VV IN9V, APL1086-33 T J =25C, IOUT =0mA, T J =0~125C, 0 IOUT 1.5A, 4.75VV IN9V, Line Regulation T J =0~125C APL1086 IOUT=10mA, 1.5VV IN -V OUT9V, (note1) APL1086-18 IOUT=0mA, 3.5VV IN9V, (note1) APL1086-25 IOUT=0A, 4VV IN9V, (note 1) APL1086-28 IOUT=0A, 4.25VV IN 9V, (note 1) APL1086-33 IOUT=0A, 4.75VV IN 9V, (note 1) Load Regulation T J =0~125C APL1086 (V IN -V OUT)=3V, 0 IOUT 1.5A ,(note 1) APL1086-18 V IN=3.5V, 0 IOUT 1.5A ,(note 1) APL1086-25 V IN=4V, 0 IOUT 1.5A ,(note 1) APL1086-28 V IN=4.25V, 0 IOUT 1.5A ,(note 1) APL1086-33 V IN=4.75V, 0 IOUT 1.5A ,(note 1) Dropout Voltage IOUT=1.5A ,T J =0~125C Current Limit (V IN -V OUT)=5V, T J=25C Adjust Pin Current (V IN -V OUT)=3V, IOUT=10mA, T J=0~125C
0.03 1 1 1 1 0.1 1 1 1 1 1.3 1500 60 0.2 1.7 60 75 0.01 0.5 0.3
0.2 6 6 6 6 0.4 10 10 10 10 1.45 120 5
% mV
% mV
V mA A A mA dB
Adjust Pin Current T J=0~125C, 10mA IOUT 1.5A, Change 1.4V(VIN -V OUT) 7.75V Minimum Load IO T J=0~125C, (V IN -V OUT)=7.75V, (note 3) Current F RIPPLE=120Hz, V RIPPLE =1V P-P, PSRR Ripple Rejection (V IN -V OUT)=3V, T J=0~125C Thermal TR T J=25C, 30ms Pulse Regulation Temperature TS Stability Long -Term LS T J =125C,1000Hrs. Stability
Copyright ANPEC Electronics Corp. Rev. A.4 - Jun., 2003 3
0.02
%/ W % %
www.anpec.com.tw
APL1086
Electrical Characteristics (Cont.)
Symbol VN th OT Parameter RMS Output Noise Thermal Resistance Over Temperature Point Quiescent Current APL1086-18 APL1086-25 APL1086-28 APL1086-33 Test Conditions T J=25C,10HzF10kHz, (% of V OUT) Junction to Case, at Tab Junction to ambient APL1086 Min. Typ. Max. 0.003 15 50 150 T J=0~125C, V IN9V V IN9V V IN9V V IN9V 5.5 5.5 5.5 5.5 10 10 10 10 Unit % C/ W C mA
Note 1: See thermal regulation specifications for changes in output voltage due to heating effects. Load line regulations are measured at a constant junction temperature by low duty cycle pulse testing. Note 2: Dropout voltage is specified over the full output current range of the device. Dropout voltage is defined as the minimum input/ output differential measured at the specified output current. Test points and limits are also shown on the Dropout Voltage curve. Note 3: Minimum load current is defined as the minimum output current required to maintain regulation.
Application Circuits
1.25V to 10.7V Adjustable Regulator
APL1086 V IN IN ADJ OUT R1 121 +
10 F
Improving Ripple Rejection
V OUT 1
V IN
10 F
+
APL1086 IN OUT ADJ
R1 121 1% + C1
10 F
V OUT 150 F
+ R2 1k
100 F
C 1*
C2
* Needed if device is far from filter capacitors
* C1 improves ripple rejection. XC should be approximately equal to R1 at ripple frequency
R2 365 1%
VOUT = 1.250Vx
R1 + R2 R1
5V Regulator with Shutdown
APL1086 IN OUT ADJ + TTL 1k
10 F
V IN
5V 121 1% + 365 1%
1k
100 F
Copyright ANPEC Electronics Corp. Rev. A.4 - Jun., 2003
4
www.anpec.com.tw
APL1086
Typical Characteristics
Load Transient Response
5 4.5 0.02
Line Transient Response
6 0.15
Output Voltage Deviation (V)
Output Current (A)
Input Voltage (V)
3.5 3 2.5 2 1.5 1 0.5 0 -100 100 300 500 700 -0.03 900 -0.02 0
0.1 4
CIN=10uF Cout=10uF Tantalum VIN=5V
3
CIN=10uF Cout=10uF Tantalum IOUT=0.1A
0.05
-0.01
2 0 1 -0.05 -20 30 80 130 180
0
Time (s)
Time (s)
Dropout Voltage vs. Output Current
1.35 1.3 1.25
Output Voltage vs. Input Voltage
3.5 3
Output Voltage (V)
Dropout Voltage (V)
1.2 1.15 1.1 1.05 1 0.95 0.9 0 0.5 1 1.5
2.5 2 1.5 1 0.5 0 0 1 2 3 4 5 6 7 8 9
Output Current (A)
Input Voltage (V)
Copyright ANPEC Electronics Corp. Rev. A.4 - Jun., 2003
5
www.anpec.com.tw
Output Voltage Deviation (V)
4
0.01
5
APL1086
Typical Characteristics Cont.
Input Current vs. Input Voltage
6
3.4
Current Limit vs. Input Voltage
Vout=1.25V
5
2.9
Input Current (mA)
3
2
1
0 0 2 4 6 8 10
Current Limit (A)
4
2.4
1.9
1.4
0.9 0 3 6 9 12
Input Voltage (V)
Input Voltage (V)
Output Voltage vs. Temperature
3 .4
Output Voltage vs. Temperature
2.6 2.5 2.4
3 .3
Output Voltage (V)
2.3 2.2 2.1 2 1.9 1.8 1.7 1.6 -50 -25 0 25 50 75 100 125
Output Voltage (V)
3 .2 3 .1
3 .0 2 .9
2 .8 2 .7 -5 0
-2 5
0
25
50
75
100
125
Temperature (C)
Temperature (C)
Copyright ANPEC Electronics Corp. Rev. A.4 - Jun., 2003
6
www.anpec.com.tw
APL1086
Typical Characteristics Cont.
A djustable P in C urrent vs. Tem perature
Input Current vs. Tem perature
68
8
7
A djustable P in C urrent ( A )
64
Input Current (mA)
6
60
5
4
56
3
52 -50
-25
0
25
50
75
100
125
2 -50 -25 0 25 50 75 100 125
Tem perature ( C )
Tem perature ( C)
Current Limit vs. Temperature
2 .9 2 .7
Current Limit (mA)
2 .5
Vin-Vout=5V
2 .3 2 .1 1 .9
1 .7 1 .5 -5 0
-3 0
-1 0
1 0
3 0
5 0
7 0
9 0
10 1
10 3
10 5
Temperature (C)
Copyright ANPEC Electronics Corp. Rev. A.4 - Jun., 2003
7
www.anpec.com.tw
APL1086
Package Information
SOT-223( Reference JEDEC Registration SOT-223)
D B1
A c
a
H
E L K e e1 b A1
B
Dim A A1 B B1 c D E e e1 H L K Min. 1.50 0.02 0.60 2.90 0.28 6.30 3.30
Millimeters Max. 1.80 0.08 0.80 3.10 0.32 6.70 3.70 2.3 BSC 4.6 BSC 6.70 0.91 1.50 0 13
8
Inches Min. 0.06 0.02 0.11 0.01 0.25 0.13 0.09 BSC 0.18 BSC 7.30 1.10 2.00 10 0.26 0.04 0.06 0 13
www.anpec.com.tw
Max. 0.07 0.03 0.12 0.01 0.26 0.15
0.29 0.04 0.08 10
Copyright ANPEC Electronics Corp. Rev. A.4 - Jun., 2003
APL1086
Package Informaion
TO-252( Reference JEDEC Registration TO-252)
E b2 L2 A C1
D H
L1 L b e1 D1 C A1
E1
Dim A A1 b b2 C C1 D D1 E E1 e1 H L L1 L2
M illim et er s M in. 2. 1 8 0. 8 9 0. 5 08 5. 2 07 0. 4 6 0. 4 6 5. 3 34 5. 2 R EF 6. 3 5 5. 3 R EF 3. 9 6 9. 3 98 0. 5 1 0. 6 4 0. 8 9 1. 0 2 2. 0 32
9
Inc he s M ax. 2. 3 9 1. 2 7 0. 8 9 5. 4 61 0. 5 8 0. 5 8 6. 2 2 6. 7 3 5. 1 8 10 . 41 M in. 0. 0 86 0. 0 35 0. 0 20 0. 2 05 0. 0 18 0. 0 18 0. 2 10 0. 2 05 R EF 0. 2 50 0. 2 09 R EF 0. 1 56 0. 3 70 0. 0 20 0. 0 25 0. 0 35 0. 0 40 0. 0 80
www.anpec.com.tw
M ax. 0. 0 94 0. 0 50 0. 0 35 0. 2 15 0. 0 23 0. 0 23 0. 2 45 0. 2 65 0. 2 04 0. 4 10
Copyright ANPEC Electronics Corp. Rev. A.4 - Jun., 2003
APL1086
Package Informaion
TO-220 ( Reference JEDEC Registration TO-220)
D Q
R
b E
e b1 e1
L1
H1
L
A F
c
J1
Millimeters Dim A b1 b c D e e1 E F H1 J1 L L1 R Q Min. 3.56 1.14 0.51 0.31 14.23 2.29 4.83 9.65 0.51 5.84 2.03 12.7 3.65 3.53 2.54 Max. 4.83 1.78 1.14 1.14 16.51 2.79 5.33 10.67 1.40 6.86 2.92 14.73 6.35 4.09 3.43 Min. 0.140 0.045 0.020 0.012 0.560 0.090 0.190 0.380 0.020 0.230 0.080 0.500 0.143 0.139 0.100
Inches Max. 0.190 0.070 0.045 0.045 0.650 0.110 0.210 0.420 0.055 0.270 0.115 0.580 0.250 0.161 0.135
Copyright ANPEC Electronics Corp. Rev. A.4 - Jun., 2003
10
www.anpec.com.tw
APL1086
Package Informaion
TO-263 ( Reference JEDEC Registration TO-263)
E L2
A c2
D L L1 L3
e
b2 b
c
M illimeters Dim A b b2 c c2 D E e L L1 L2 L3 M in. 4.06 0.51 1.14 0.38 TYP. 1.14 8.64 9.66 2.543 BSC. 14.60 2.24 1.20 15.88 2.84 2.92 1.78 0.575 0.090 0.050 1.40 9.65 10.299 0.045 0.340 0.380 M ax. 4.83 0.992 1.399 M in. 0.160 0.02 0.045
Inches M ax. 0.190 0.039 0.055 0.015 TYP. 0.055 0.380 0.405 0.100 BSC. 0.625 0.110 0.115 0.070
Copyright ANPEC Electronics Corp. Rev. A.4 - Jun., 2003
11
www.anpec.com.tw
APL1086
Physical Specifications
Terminal Material Lead Solderability Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb) Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3.
Reflow Condition
(IR/Convection or VPR Reflow)
Reference JEDEC Standard J-STD-020A APRIL 1999
temperature
Peak temperature
183C Pre-heat temperature
Time
Classification Reflow Profiles
Convection or IR/ Convection Average ramp-up rate(183C to Peak) 3C/second max. 120 seconds max Preheat temperature 125 25C) 60 - 150 seconds Temperature maintained above 183C Time within 5C of actual peak temperature 10 -20 seconds Peak temperature range 220 +5/-0C or 235 +5/-0C Ramp-down rate 6 C /second max. 6 minutes max. Time 25C to peak temperature VPR 10 C /second max.
60 seconds 215-219C or 235 +5/-0C 10 C /second max.
Package Reflow Conditions
pkg. thickness 2.5mm and all bgas Convection 220 +5/-0 C VPR 215-219 C IR/Convection 220 +5/-0 C pkg. thickness < 2.5mm and pkg. volume 350 mm pkg. thickness < 2.5mm and pkg. volume < 350mm Convection 235 +5/-0 C VPR 235 +5/-0 C IR/Convection 235 +5/-0 C
www.anpec.com.tw
Copyright ANPEC Electronics Corp. Rev. A.4 - Jun., 2003
12
APL1086
Reliability test program
Test item SOLDERABILITY HOLT PCT TST ESD Latch-Up Method MIL-STD-883D-2003 MIL-STD-883D-1005.7 JESD-22-B, A102 MIL-STD-883D-1011.9 MIL-STD-883D-3015.7 JESD 78 Description 245C , 5 SEC 1000 Hrs Bias @ 125 C 168 Hrs, 100 % RH , 121C -65C ~ 150C, 200 Cycles VHBM > 2KV, VMM > 200V 10ms , Itr > 100mA
Carrier Tape & Reel Dimensions
t P P1 D Po E
F W
Bo
Ao
Ko D1
T2
J C A B
T1
Application
A 330 3
B 100 2 D
C 13 0. 5 D1
T1 T2 16.4 + 0.3 2.5 0.5 2 0.5 -0.2 Po P1 Ao
J
W 16+ 0.3 - 0.1 Bo
P 8 0.1 Ko
E 1.75 0.1 t
TO-252
F
7.5 0.1 1.5 +0.1 1.5 0.25 4.0 0.1 2.0 0.1 6.8 0.1 10.4 0.1 2.5 0.1 0.30.05 Application A 3803 TO-263 F B 80 2 D C 13 0. 5 D1 J 2 0.5 Po T1 24 4 P1 T2 2 0.3 Ao W 24 + 0.3 - 0.1 Bo P E 16 0.1 1.75 0.1 Ko t
11.5 0.1 1.5 +0.1 1.5 0.25 4.0 0.1 2.0 0.1 10.8 0.1 16.1 0.1 5.2 0.1 0.350.01 3 (mm)
Copyright ANPEC Electronics Corp. Rev. A.4 - Jun., 2003 13 www.anpec.com.tw
APL1086
Reel Dimensions (Cont.)
Application A 3301 SOT-223 F B 621.5 D C 12.75 0.15 D1 J 2 0.6 Po T1 12.4 +0.2 P1 T2 2 0.2 Ao W 12 0.3 Bo P 8 0.1 Ko E 1.75 0.1 t
5.5 0.05 1.5+ 0.1
1.5+ 0.1 4.0 0.1 2.0 0.05 6.9 0.1 7.5 0.1
2.1 0.1 0.30.05 (mm )
Cover Tape Dimensions
Application TO- 252 TO- 263 SOT- 223 Carrier Width 16 24 12 Cover Tape Width 13.3 21.3 9.3 Devices Per Reel 2500 1000 2500
Customer Service
Anpec Electronics Corp. Head Office : 5F, No. 2 Li-Hsin Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 7F, No. 137, Lane 235, Pac Chiao Rd., Hsin Tien City, Taipei Hsien, Taiwan, R. O. C. Tel : 886-2-89191368 Fax : 886-2-89191369
Copyright ANPEC Electronics Corp. Rev. A.4 - Jun., 2003
14
www.anpec.com.tw

▲Up To Search▲

Price & Availability of APL1086

	To Download APL1086 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .